Free Energy from Atomic Hydrogen
The MAHG Project
Created on May 23, 2005 - Updated on June 2, 2005
Free Energy from Atomic
Hydrogen
The MAHG Project
Created on May
23, 2005 - Updated on June 2, 2005
The Moller's Atomic Hydrogen Generator (MAHG) is fully based on the Irving Langmuir discovery. In the MAHG, the hydrogen is merely dissociated and recombined and can therefore be recycled over and over again without consuming more hydrogen than the quantity used to start with.
The Atomic Hydrogen Process is 100% CLEAN and SAFE.
The MAHG tube has been specially
designed : It is composed by a water cooled vaccum tube filled
with hydrogen at 0.1 atm.
The main part of the MAHG is a tungsten filament (0.25 mm
diameter) placed in the center.
In the MAHG the hydrogen is NOT consummed during the process.
The MAHG under test (DC pulsed
mode)
The MAHG under test (pure DC mode)
A close view to MAHG device
A Metrix MTX3352-C (100 MHz)
digital oscilloscope is used to measure the power input
The electric power input is measured with 3 different means :
Analog Voltmeter and Ammeter with a high current shunt,
Digital Voltmeter and Ammeter (Fluke 189) with a current clamp (VC 601),
Digital oscilloscope (MTX3352-C) with a current clamp (VC 601).
In these 3 cases the voltage and the current measured at the input are still in the same range ( +/- 2% of variations )
Videos of the MAHG under test
Click on the picture to see the video (2.64 Mb )
Click on the picture to see the video (1.63 Mb )
Data sheet results details :
Input (V), Input (A) : Rms Voltage and Rms Current at the input
Mode : Mono Alt, single DC pulse mode (half sine wave) at 50% of duty cycle
S_F_m3/h : Water flow measured at the start of the run in m3/h
F_F_m3/h : Water flow measured at the end of the run in m3/h
AVG_F : Average flow of water during all the run in m3/h
Variac : percent of value of the auto-transformer cursor, a (+) has been set to indicate that the input has been boosted with an additional transformer
Vent : Setup of the fan
Ts1 : Output temperature of the water at the start of the run
Ts2 : Input temperature of the water at the start of the run
T Offset = Ts1 - Ts2 : temperature correction value for the initial conditions
Tf1 : Output temperature of the water at the end of the run
Tf2 : Input temperature of the water at the end of the run
dT : Temperature difference at the end of the run, dT = (Tf1 - Tf2) - (T Offset)
PWR INP : Electrical power at the input
PWR OUT : Thermal power at the output :
Power OUTPUT = Flow Rate (m3/h) x dT (°C ) x ( 4,18 x 106 / 3600 ) = Flow Rate (m3/h) x dT (°C ) x 1161,11
Efficiency = Power OUTPUT / Power INPUTAdditional comments :
RUNS 1 to 10 have been conducted for tuning purposes and mechanical adjustments.
The full tests datas used in the graphs in DC pulsed mode have been conducted between the RUN 11 to 37.
RUNS 26 to 37 have been done with the same current level (about 67 A) to check the variability of the results. The average efficiency measured has been 224% with a net power gain of 464 Watts.
RUNS 38 to 40 have been performed with a PURE DC current. The pulsed transformer unit has been replaced with a High Current DC Power Supply. As you may notice in the experimental results, the average efficiency measured has been 64%, so there are 36% of losses in the device. With pure DC, the filament temperature (774 °K) is not sufficient to create the hydrogen dissociation process which requires at least 2000°K. RUNS 38 to 40 can be considered as BLANK TESTS of the MAHG reactor, see the curve of "Temperature of the filament VS Time" below.
The Current Vs Voltage curve : you may
notice that the resistance of the tungsten filament is non
linear.
The curve above shows the percentage
of hydrogen dissociated into atomic hydrogen Vs the temperature
of the tungsten.
These datas have been published by Irving Langmuir in March 1926.
The temperature
(in°K) of the filament is calculated with the formula : T =
(P/kS)1/4
S: Surface of the cathod = 10-3
m2
P: electrical input power in Watt
k: 5.67 x 10-8
The experimental curve above shows the
MAHG filament (the cathod) temperature VS time during the tests.
You may notice that atomic hydrogen (1% to 7%) has been produced
during only 25 ms each 100 ms.
During the pure DC tests, the filament temperature (774 °K) is
not sufficient to create the hydrogen dissociation process which
requires at least 2000°K.
Above :The Power I/O Vs the
Voltage, the red curve shows the POWER OUTPUT and the blue curve shows the POWER INPUT
Above : In red, the curve of the Power OUTPUT Vs the Power
INPUT, the green curve is for 100% efficiency.
Comments from Jean-Louis Naudin : Today, after a lot of tests of the MAHG, I am able to confirm the previous results conducted by A. Frolov during the genesis phase of the project. The results are stable and fully reproducible although measured with a completly different set of electronic equipments. The MAHG is one of the best device that I have tested until today. It seems a very good candidate unit which can be used to produce a clean and independant energy source for our next future and for the benefit of All...
For more informations, please contact Jean-Louis Naudin at : jnaudin509@aol.com
| The Atomic Hydrogen
Process is 100% CLEAN and SAFE. When you add the fact that the hydrogen is not consumed in the “burning” process, and can thus be recycled, it should become very clear to any scientist, humanist, environmentalist, business executive and indeed to every human being that is concerned about the state of our wonderful planet, that no more time should be wasted. The time has come for removing the responsibility of defining the energy policies and structures of the future from the hands of the established energy industries, and place it in the hands of men of science who will work for the preservation of the environment that sustains all life on Earth. Men who will work for the economic development of the third world by means of providing clean, abundant and inexpensive energy technologies. Such initiative will only succeed when massively supported by the visionary captains of industry who will have the courage to dismantle the existing and scandalous energy grid which now envelopes our planet, by investing in the production and marketing of small energy generators for individual households, factories, transport etc. Once such a generator has been acquired by the consumer, his further energy requirements will be covered for FREE, giving him independence in terms of energy as well as increased buying power for any other economic development.
|
The Irwing Langmuir Atomic Hydrogen by Nicholas Moller
To the MAHG project home page
visitors since May 24, 2005
